57 Responses to Wood Burning with Ammonium Chloride

    • Hi Lesley, I haven’t tried it myself yet but I’ve seen a few other videos of people that have with success! I don’t think it would damage the rubber.

  1. How about making a stencil with vinyl. Paint in the words, remove the vinyl and use the heat gun. Meredith, do you think that would work? The vinyl would keep it from bleeding. DOes the solution need to be wet when you use the heat gun or can it be dry?

    • Hi Kate, you could definitely try it! It will work with after the solution has dried, too. My concern is that the solution would bleed under the stencil since it is so thin. It’s on my list to try, though – I am planning to use the stencil and paint over it with mod podge, then peel up the vinyl and paint with the solution, so the wood will burn where the vinyl was. Make sense? If you try it either way let me know how it works out!

        • Do you mean with the stencil? I actually haven’t gotten around to trying it yet but I have some ideas for Christmas gifts so I will be trying it soon! I will update this post with links to the tutorial once I publish a new tutorial!

          • You should use “Thick It” with the Ammonium Chloride so that it doesn’t bleed.

  2. I tried this with raw wood but the painted letters just bleeded and flowed. It seems like the surface was too rough. Can I first use a sander to get it more smooth?

    • Hi Lindie, I had something similar happen the first time too. It takes a VERY small amount of solution on your brush! You could even use a paper towel to blot the brush and get off any excess. And yes, a smoother surface will probably help, too, so you could try sanding it down.

    • Yes, it’s more of a brand and the surface stays pretty smooth (unlike a wood burning tool which puts small indents in the wood with the burns) but it does chemically burn the wood.

    • Hi Jessica, there really isn’t any drying time at all! As soon as you apply the solution you can use the heat gun, you don’t have to wait for it to dry. Is that what you mean? But even if you do let it dry before you use the heat gun, it still works the same way.

      • I’ve used the commercially available pens with good results. I bought a jar of ammonium cloride from an aquatics supplier, mixed as you suggested and it does not change colors. I added more chemical in stages untill all I got was a white powder when heated. What am I doing wrong?

        • For me that happened when I was trying to use a hair dryer…I only got the burn when I was using the heat gun. Maybe you need more heat?

  3. Hello Meredith!

    I am looking to use this for a Father/Daughter craft idea. Do you have to wear a mask or gloves? Is it safe to breath in.

    • Hi Blayne, I really couldn’t say for sure…I didn’t wear a mask or notice any fumes but you’ll want to do your own research just to be safe. Gloves are probably a good precaution.

  4. Hello,
    I attempted this by making a vinyl stencil! I put the decal on the cutting board purchased from Walmart. Then applied varnish and removed the vinyl. Applied the ammonia chloride but it bled around where the decal was. Do you know how to avoid this? Thank you!

    • I know how to prevent bleeding. However this is 3 years later…thicken your solution with cornstarch! You still should only try to get the liquid in the stencil area. I spray my entire piece with Rustoleum clear mat spray. I apply about three coats. Don’t worry it dries quick, I just want to make sure every corner has been covered correctly. When you remove stencil you can easily see where to apply liquid. I also blot with a paper towel as I apply. If you should have some bleeding you can use an exacto knife and gently scrape (with the grain) off the part you wish did not bleed through!

      • Glad you made the comment 3 years later, it worked for me :)
        I use a Cricut to cut vinyl decals, paint it on, let it dry, and pull up the decal.

  5. Did you do this technique on the “I Am His” using the print out you provided on the original post about it? Just curious….we are hosting a ladies day at our congregation with the theme Daughter of the King and thought this would be perfect. But would definitely like to watch a tutorial if you’ve done it already! Thanks. KL

    • Hi Krystal, no, the “I am His” sign was a different technique that’s actually an image transfer…this one is wood burning. I don’t have a video tutorial for that one, unfortunately.

  6. I would like to make one of these as a table centerpiece where people can put their hot pans on it. Do I need to put something on top of it to protect it?

    • Great idea! I don’t think you’d need to do anything to protect it, as it’s the same as a wood burned design – it’s literally burned into the wood, so nothing is going to scuff it off. But if you’d like a more “finished” surface, adding a coat of Mod Podge or polyurethane would work well.

  7. Hi, I wondered if you could help me?

    I’ve been trying this idea for a couple of weeks now and have had no luck, followed all the steps and others who have done a similar thing. I’ve used a stamp and hand painted onto wood however, as soon as I put my heat gun on the wood, the ammonium chloride solution just dries as if nothing is there, so it just leaves me with a blank piece of wood.

    Any idea what I can do?

    • I don’t have a lot of experience with this technique so I’m not quite sure why that’s happening…but here are some troubleshooting ideas! What kind of wood are you using? Is it possible it’s been treated somehow and isn’t letting the solution soak into the wood? You might also try a bit of a stronger solution. Or it could be that the stamp isn’t transferring enough of the solution, so maybe try just painting on the wood to see if that works?

      • It could also be that the heat gun isn’t hot enough. I tried a hair dryer and that did the same thing you’re describing – just dried the solution without making any mark on the wood – because it wasn’t nearly hot enough.

        • the wood in untreated and I’ve tried painting, so perhaps its not hot enough like you say! I will have to take it back and invest in a better one I think! Thanks for your help. It does feel more like a hairdryer as you describe.
          thanks

          • I’m not sure of the voltage but the temperature settings of my heat gun are 750*F to 1100*F. (The one linked to in the supplies list at the beginning of the post is the one I have)

    • You should wait until your solution dries to begin heating it up. Otherwise it turns to what you just described. But you can take a razor and gently scrape away the white powder and reapply.
      I also just posted some tips on how to prevent bleeding and removing bleeding as well a few questions above yours. These tips have helped me tremendously throughout my trial and error. To know the amount of cornstarch to add just Google how much cornstarch should I add to X amount of liquid for a paint or honey consistency.

  8. To prevent bleeding maybe try frog tape to make ur stencil. I use for paint stenciling. Let me know if it works w this. Have too many.projects going now but would like to try this method.

  9. What brand of ammonium chloride did you purchase and where? Locally all I can find is a 45lb bag of it at the AG store. Also, from what I’ve read, when you mix the solution, you are supposed to use warm water, as you stated as well. Thank you for the helpful tips and info!

  10. I love how easy simply and clear while including tips & ‘tricks’ from your experience working with the ammonium chloride. Thank you.
    I am, however, curious about a few things with this chemical and maybe I am not using the best ‘search’ words to locate the answers and hoping you might know.
    While I realized that 1TBSP from 1lb is minor, wondering IF you have remaining solution, can it be saved for future projects? If so, best way to store it? What would the shelf life of that mix be? And, would it be possible to rewarm it without issue?
    I was hoping to salvage remaining portion in a glass jar, preferably with a lid; rewarming it in a dish of warmer water, IF this is feasible. Please let me know your thoughts. Again, thank you for your awesome post on this chemical and DIY.

    • Hi Tina, I’m sorry I don’t know! I would err on the side of caution and say you should discard the solution when you’re finished with it and mix up a new batch for each project.

  11. Hi Meredith,

    Thanks for your post on this wood branding technique.

    I was just wondering if you knew long ammoniumchloride left outdoors lasts? I make garden furniture and its left fully exposed… I’m curious how long these wood burns last and if they still look good after several years.

    Many thanks :)
    Cedric

    • Hi Cedric, I don’t have any firsthand experience with branding outdoor items, but this technique is actually a chemical wood burn, so once the wood is burned it doesn’t wash away or anything like that. I’d imagine as long as you seal/treat the furniture the way you would otherwise the wood burn would be permanent.

  12. You can use a small amount of xanthum gum or a product used for thickening food to the solution to control the ‘running’ solution. Found it on a ‘cricut’ tutorial. Don’t remember details but shouldn’t be hard to find it … You Tube

  13. WOW, thank you so much for all the helpful information! Your original posts are apparently before the chemical pens came out. They’re sooo expensive I thought perhaps I might be able to find what chemical is used and do it myself at home. Low and behold your posts came up!!! I’m so excited! Thank you to too the gal about the xanthum gum to thicken the solution.

    • Cornstarch works great too! I used 1TBSP of cornstarch with 7 TBSP water and heated in microwave for 1 minute and then stirred in 1 Tbsp Ammonium Chloride. No bleed whatsoever!!! But the heat gun warped my board. Hmmmm now to problem solve that!!

  14. I am just now learning about this wood burning technique. My friend did it on a cutting board as a wedding gift for her friend but I can’t find anything that tells me it it’s a food safe OPTION for a cutting board. The board looks awesome but will the people be able to USE it or is it just decorative now?

Leave a Reply to Cami Cancel reply

stay-at-home mom to three beautiful children, wife to an incredible husband, and daughter of a loving God. I freely admit that I am not always the most creative or original person when it comes to crafting, decorating, organizing, cooking, etc...but I love being inspired by great ideas and putting my own spin on them! Look around, stay a while, and I hope through my *unoriginality* I can provide some inspiration to you, too!
Read More...

Click the button above and use code 10OFF to get 10% off regular priced items! (bundles and promo items not included)

Unless otherwise stated, all words and photos on this blog are my own and are copyrighted by unOriginal Mom. If you'd like, you may use 1 (ONE) photo, without altering them in any way, including removing the watermark, but you must attribute proper credit and a link back to this site. I would also appreciate a comment letting me know so I can visit! The text of this blog or multiple photos should NOT be copied and re-posted elsewhere without permission.